Electronic Theatre Controls PARADIGM Spezifikationen PDF herunterladen (Seite 79)

4 Service 74

Hardware Reset Switch

Reset the Paradigm ACP software and hardware by pressing the reset switch located on

the front panel of the unit. You can access this reset switch using the tip of a ball point pen,

or other pointed object.

During a powered reset the host rack holds levels for the last look played until the Paradigm

ACP has rebooted and takes control.

reset switch

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 95 96

Configuration Manual 1
Table of Contents 3
Appendix A 5
Appendix B 5
Introduction 6
Contacting ETC 8
Rack and System Feedback 10
Control Inputs 10
Introduction 6 11
CAUTION: 12
Overview 13
Install the Paradigm ACP 14
System Status 15
User Interface Overview 16
Recent/And 17
#Nav/Thru 18
Alpha Search 18
USB Port 19
SD Media 19
Reset Switch 20
Paradigm ACP Basic Navigation 21
Dimming Rack Status 22
System OK 22
DMX Start = 1 22
Ø1: 119 Ø2: 119 Ø3: 120 22
60Hz 102F v1.0.2 22
Arch Control Status Display 23
Status / Error Messages 24
Menu Navigation 27
Programming 28
About Menu 29
DMX Input 30
DMX Output 30
3 Programming 26 31
Version Info 31
Project Information 31
Statistics 31
Ethernet Interface 32
LON Interface 32
3 Programming 28 33
View Message Log 33
System Network 33
Stations and LonWorks 33
Connected 34
Unconnected 34
Found w/ Error 34
Dimming Setup Menu 35
Module Type 36
Dimmer Setup 36
100 - 120 VAC Racks 37
277 VAC Racks 37
230 and 240 VAC Racks 37
3 Programming 34 39
Dynamic Preheat 40
Transformer Mode 40
DMX Res: 40
Patch by DMX Start 41
Patch Dimmers 42
Attention: 43
Emergency Dimmers 44
Emergency Level 44
Emergency Setup 45
Apply Changes* Only 46
Apply Changes* Only 46
3 Programming 42 47
LonWorks Connections 48
3 Programming 44 49
Assign Processor / IP 49
Date/Time/Location 50
3 Programming 46 51
Preferences 52
3 Programming 48 53
Data Loss and Power On 53
DMX Settings 54
Dimming Control Menu 55
Dimming Control 55
Set Levels 55
1 and 5 thru 12 55
Dimmer Check 56
Release Set Levels 56
<All> Presets 57
Select Space 57
Control Channels 58
3 Programming 54 59
Sequences 60
3 Programming 56 61
Overrides 61
Clear Arch Output 61
File Operations Menu 62
Save Rack Configs 62
Save Filename 62
Save Dimming Config 63
Rack Size Mismatch 64
Save Arch Config 65
Cannot Perform Save 65
<Enter to continue> 65
WARNING: 66
Restore Defaults 67
Update Firmware 68
Save LCD Files 69
Save Log Files 69
3 Programming 64 69
View/Clear Errors Menu 70
View/Clear Errors 70
Restricted Access Menu 71
Restricted Access 71
Change Admin Passcode 72
Timed Event Setup Menu 73
Main Menu 73
Timed Event Setup 73
3 Programming 70 75
Add New Event 75
Chapter 4 77
Service and Maintenance 78
4 Service 74 79
Hardware Reset Switch 79
Paradigm ACP Menu Flow Chart 80
Menu Flow Chart 81
Recurrence Type 86
Configure Recurrence 86
Attention 86
End Time 86
Start Time 86
Dimmer Specifications 88
240 VAC Dimmer Modules 89
277 VAC Dimmer Modules 89
230 VAC Dimmer Modules 89
Dimmer Module Defaults 90
Dimmer Modes 91
2 and 3 Wire Fluorescent Mode 92
4 Wire Fluorescent Mode 92
Always On Mode 92
DALI Mode 92
Off Mode 93
Reverse Phase Mode 93

Kommentare zu diesen Handbüchern

Keine Kommentare

Electronic Theatre Controls PARADIGM Spezifikationen Seite 79

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Navigatoren Electronic Theatre Controls PARADIGM